| Subject | Text |
| SONY Book Shelf Stereo FH-B511 Model No. HCD-H550 No Power | Hi All,
Hope you can help with the above unit.
The Power supply appears to be generating the r |
| Casio DA1 Portable AT Machine | Hi
Need a Service Manual for Casio DAT recorder Model DA1
Showing Power Down message even when o |
|
|
| resolder all joints in the line output stage, check R629 (27ohms, 1/2w 90 degree tube)(2.7ohms, 1/2w |
| Re: yamaha RX-V1800 | [quote:e5feb97d31="[email protected]"]I just had my RX-V1800's dsp assembly changed as what the yam |
| Explanation or website for learning about RF and IF stages? | Hello everyone. Could someone either supply a good website address (I have tried Googling) or please |
| Re: Beko tv | [quote:a5d8c0a799="Old bassid"]Lissen whippersnapper!- how do you know your ir works- have you got a |
| Speakers and wiring are good. The distortion is there regardless of input - whether internal (tuner) |
| Nissan Primera SVE Service reminder Info Please | Many thanks for replying ourbabyboo. I use the site regularly and offer assistance to others if I ca |
| :D [b:9f21187ecd][i:9f21187ecd]if your picture is too wide horizontally and vertically you either ha |
| kenwwod | Hello,
Most probaly in this case is that your end stage is faulty.
Mostly the transistors on the c |
| IF THE LINES ARE VERTICAL IE TOP TO BOTTOM THEN VERT STAGE IS OK AND FAULT IS IN LINE, UNUSUAL TO GE |
| Hi! I think you should replace the electrolyt capapitors in stage of frame the tv-set. Rgr |
| The audio bandwidth is not a large problem.
An ordinary fixed telephone line typically has a bandwi |
| power supply question | Hi
when you say primary of the power supply, what specifically?
Is this a switching or linear |
| sharp geometry problem (pincushion) | Dear Mario,
I guess that "RESOLDER THE FLYBACK CAPACITORS IN THE LINE OP STAGE" means replacing b |
| Kenwood KAC-PS500F 4channel Car amp: No sound output | Kenwood PS500F 4 channel Car amp Schematics or Service advice needed. Can anyone help with any usefu |
| CASIO DA-2 | Does anyone have a service manual for the DAT CASIO DA-2? |
|
|
| Found that 15v regulator is stuffed. Suspect that 15v rail on the analogue input stage is shorted. J |
| It should be operational without the Remote... at a pinch I wouldn't be surprised if it's 'tripping' |
| zenith tv | I assume it turns on now and again?
Depends on various factors is the standby led lit?
if not the |
| I use to come across this on variety of different brands. Sort of a catastrophic failure where the d |
| FREE:
I hope mine don't ever do dat.
[url]http://elektrotanya.com/acer_x193w_sm.pdf/download.htm |
| Re: Polishing of Silicon wafers | [quote:c090204838="Saurav"]Hi,
I have come across a technological development where we are a |
| Re: Sony tv | [quote:e2732ed2eb="picasso"]Hi Buddy 128,
Resolder vertical output stage and check R518 , R519 (0 |
| Trouble shooting systems | [quote:36d03f5807="Anonymous"]After 46 years servicing electronics, there is one thing that never fa |
| I need EDID for LCD monitor AOC 416V | I need EDID data ( Dsub or DVI input ) for LCD monitor AOC 416V ( 24 inch , res 1920 x 1200 ) in any |
| i should certainly check the soldering in lopt stage ie flyback transformer line drive tranformer an |
| 13 flashes of the front led is telling you there is a fault in the frame stage normally dry joints o |
| sounds like you have a dry joint, try resoldering all the hv caps in the line output stage, these ar |
| Sony WM-D6c | Disassembled to fix no FF, No rew problem and replaced the belt and a needed Mic jack. After re-ass |